4．振幅的调整（见图四）振动电机上下装有两对扇形偏心块，通过调整两对偏

4．振幅的调整（见图四）振动电机上下装有两对扇形偏心块，通过调整两对偏心块的相对位置来改变激振力的大小，从而改变振幅的大小。振幅可在0～6毫米内调整，最大不得超过6毫米，本机出厂时，一般调为4～4.5毫米。振幅的大小取决于每对扇形偏心块重合面的大小，重合面大则振幅大，重合面小则振幅小。加大振幅则提高生产率，减小振幅则降低生产率。

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

4. Amplitude adjustment (see Figure 4) The <br>vibration motor is equipped with two pairs of fan-shaped eccentric blocks above and below. By adjusting the relative position of the two pairs of eccentric blocks, the magnitude of the exciting force is changed, thereby changing the magnitude of the amplitude. The amplitude can be adjusted within 0～6mm, and the maximum shall not exceed 6mm. When the machine leaves the factory, it is generally adjusted to 4～4.5mm. The magnitude of the amplitude depends on the size of the coincident surface of each pair of fan-shaped eccentric blocks. The larger the coincident surface, the larger the amplitude, and the smaller the coincident surface, the smaller the amplitude. Increasing the amplitude increases productivity, and reducing the amplitude decreases productivity.

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

4． Adjustment of amplitude (see Figure IV)<br>The vibration motor is equipped with two pairs of fan-shaped eccentric blocks up and down, which change the size of the amplitude by adjusting the relative position of the two pairs of eccentric blocks. Amplitude can be adjusted within 0 to 6 mm, the maximum should not exceed 6 mm, the factory, generally adjusted to 4 to 4.5 mm. The size of the amplitude depends on the size of the coincident face of each pair of fan-shaped eccentric blocks, while the large remedant face has a large amplitude and a small re-closing surface. Increasing the amplitude increases productivity, while reducing the amplitude reduces productivity.

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

4. Adjustment of amplitude (see Fig. 4)<br>There are two pairs of fan-shaped eccentric blocks on the top and bottom of the vibration motor. By adjusting the relative position of the two pairs of eccentric blocks, the magnitude of the exciting force is changed, so as to change the amplitude. The amplitude can be adjusted within 0-6 mm, and the maximum is not more than 6 mm. When the machine leaves the factory, it is generally adjusted to 4-4.5 mm. The amplitude depends on the size of the coincidence surface of each pair of sector eccentric blocks. The larger the coincidence surface is, the larger the amplitude is. The smaller the coincidence surface is, the smaller the amplitude is. Increasing amplitude increases productivity, while decreasing amplitude decreases productivity.<br>

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.