(1)设备处于开启状态时，用户不能从折弯机的刀口伸手进去调节后挡位。(

(1) When the device is on, a user can not reach into the machine from the bending edge after the adjustment gear. <br>(2) processing of parts, the outer part of the stand should be movable range so as not to bruise. <br>(3) When the processing of large workpieces, preferably human standing side of the workpiece to facilitate operation. When the operator to stand, it can not affect the balance of the body due to the movement of the workpiece. <br>(4) when operating with close blade hands must place against the lower mold. Avoid accidental finger extends into the knife! <br>(5) Remove the tool neither on the bending machine can not be folded against the. In order to avoid falling knives injured people. <br>(6) When installing the tool, the tool has been secured after the acknowledgment allows the upper and lower dies are separated. When removing the tool, the tool allows hands help steady after the upper and lower molds separated. <br>In addition, and also pay attention to ensure the integrity of the mold apparatus, including: <br>(1) when installing the tool, always pay attention to the upper and lower dies gap, should be controlled within the normal range. <br>(2) installed after the mold, the lower mold promptly check whether fastened. Displacing the lower die to avoid damage to the tool. <br>(3) during the test run, the upper and lower molds in accordance with the minimum gap data to check whether the correct input.

(1) When the device is on, the user cannot reach in from the bender's knife to adjust the rear gear.<br>(2) When machining parts, people should stand outside the range of the parts to avoid being injured.<br>(3) When processing large workpieces, people are best to stand on the side of the workpiece in order to facilitate the exercise. When operating, people should stand firm, not because of the movement of the workpiece and affect the balance of the body.<br>(4) When operating closely with the knife, both hands must be in the proper position of the lower mold. Avoid accidental finger reach into the knife!<br>(5) The removed tool cannot be placed on the bender or against the bend. To prevent the tool from falling and injuring people.<br>(6) When installing the tool, confirm that the tool has been tightened before the upper and lower molds can be separated. When removing the tool, the upper and lower molds can only be separated by holding the tool with both hands.<br>In addition, we should also pay attention to ensure the integrity of molds and equipment, including:<br>(1) When installing the tool, always pay attention to the gap between the upper and lower molds, should be controlled in the normal range.<br>(2) After the mold is installed, check whether the mold is fastened in time. Avoid damage to the tool due to downward shift.<br>(3) During the trial run, check that the data input is correct according to the minimum gap of the upper and lower models.

(1) When the equipment is in the open state, the user can not reach in from the blade of the bending machine to adjust the rear gear.<br>(2) When processing parts, people should stand outside the moving range of parts to avoid being hurt.<br>(3) When machining large workpieces, it is better to stand on the side of the workpieces for easy operation. During the operation, people should stand steadily and not affect the balance of the body due to the movement of the workpiece.<br>(4) When operating close to the knife edge, both hands must lean against the appropriate position of the lower die. Avoid accidental penetration of fingers into the blade!<br>(5) The removed tool cannot be placed on the bending machine or against the bending. In order to avoid injury caused by falling of the knife.<br>(6) When installing the tool, make sure that the tool has been fastened before the upper and lower dies are separated. When the tool is disassembled, the upper and lower dies can be separated only after holding the tool with both hands.<br>In addition, pay attention to ensure the integrity of the mold and equipment, mainly including:<br>(1) When installing the tool, always pay attention to the clearance between the upper and lower dies, which should be controlled within the normal range.<br>(2) After the mold is installed, check whether the lower mold is fastened in time. Avoid tool damage due to die shifting.<br>(3) During the trial operation, check whether the data input is correct according to the minimum clearance between the upper and lower die.<br>