但是,辊轴的刚性是和其截面模量相关的。它受设备结构及其它因素的限制。我们不可能将辊轴做得特别粗。在此情况下,卷板机制造厂家应该根据卷板机的长的英语翻译

但是,辊轴的刚性是和其截面模量相关的。它受设备结构及其它因素的限制。我

但是,辊轴的刚性是和其截面模量相关的。它受设备结构及其它因素的限制。我们不可能将辊轴做得特别粗。在此情况下,卷板机制造厂家应该根据卷板机的长度及卷板材质的性能、板厚等不同参数,考虑将各辊轴设计成略带弧形即对辊轴进行弧形修正。不过这只适用于一定的板材厚度范围。弧形修正目的:在卷板过程中,当上下辊受力出现挠曲变形后,使得其夹持板材的部分基本趋平直。即,保证夹持板材的上下辊之间的间隙一致,使板材沿辊轴长度方向各点受力均匀。弧形尺寸的大小应根据材质及适用的板料厚度范围等参数,由经验丰富的专业技术人员进行慎密的计算。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
However, the rigidity of the roller shaft is related to its section modulus. It is limited by equipment structure and other factors. It is impossible for us to make the roller extremely thick. <br>In this case, the bending machine manufacturer should consider the design of each roller to be slightly curved according to the length of the bending machine, the performance of the coil material, and the thickness of the plate. But this only applies to a certain range of sheet thickness. <br>The purpose of the arc correction: <br>In the process of bending, when the upper and lower rollers are subjected to flexural deformation, the part holding the plate is basically straightened. That is, it is ensured that the gap between the upper and lower rollers holding the plate is consistent, so that the plate is uniformly stressed at all points along the length of the roller shaft. <br>The size of the arc should be carefully calculated by experienced professional and technical personnel according to the material and applicable sheet thickness range and other parameters.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
However, the rigidity of the roller is related to its cross-sectional modulus. It is limited by the structure of the equipment and other factors. We can't make rollers particularly thick.<br>In this case, the roller manufacturer should consider the design of each roller shaft into a slightly curved arc, that is, the roller shaft arc correction according to the length of the roll plate machine and the performance of the roll plate material, plate thickness and other parameters. However, this applies only to a certain sheet thickness range.<br>Arc correction purposes:<br>In the process of rolling plate, when the upper and lower roller forces appear to be flexdeformation deformation, so that the part of its clamping plate is basically straight. That is, to ensure that the gap between the upper and lower rollers of the clamping plate is consistent, so that the plate along the roll length direction of each point of the force uniform.<br>The size of the arc size should be based on the material and the applicable plate thickness range and other parameters, by experienced professional and technical personnel to carry out careful calculation.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
However, the rigidity of roller shaft is related to its section modulus. It is limited by equipment structure and other factors. It is impossible for us to make the roller shaft very thick.<br>In this case, the rolling machine manufacturer should consider to design each roller as slightly curved according to the length of the rolling machine, the performance of the rolling material and the thickness of the plate, that is, to correct the roller shaft by arc. However, this only applies to a certain range of sheet thickness.<br>Purpose of arc correction:<br>In the process of plate rolling, when the upper and lower rollers are subjected to bending deformation, the part of the plate clamped by them tends to be straight. That is to ensure that the gap between the upper and lower rollers of the clamping plate is consistent, so that the stress on each point of the plate along the length direction of the roller shaft is uniform.<br>The size of arc size shall be calculated carefully by experienced professional technicians according to the material and applicable plate thickness range.
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: