对于上辊而言：问题肯定是上辊下压量太大，而辊子的强度安全系数不足。这时

对于上辊而言：问题肯定是上辊下压量太大，而辊子的强度安全系数不足。这时，就要考虑设计上要有相对回旋的空间。卷板过程分步骤、合理地一次进行。对于下辊而言：问题在于没有经过初期的磨合阶段。下辊扭矩比正常工作的磨合，额外增加了不少磨损扭矩。从而综合应力加大而失效。故应当适当加粗下辊、并预先空转，则可防患于未然。

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

For the upper roller: the problem must be that the pressure of the upper roller is too large, and the strength safety factor of the roller is insufficient. At this time, it is necessary to consider the space for relative maneuver in the design. The rolling process is divided into steps and carried out at a reasonable time. For the lower roll: the problem is that it did not go through the initial run-in stage. The torque of the lower roller is more abrasion torque than the normal running-in. Thus, the comprehensive stress increases and it fails. Therefore, the lower roller should be thickened appropriately and run idling in advance to prevent trouble.

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

For the upper roller: The problem must be that the pressure on the roller is too large, and the strength safety factor of the roller is not enough. At this point, it is necessary to consider the design of a relatively leeway space. The roll board process is carried out in a step-by-step and reasonably one-time process. For the lower roller: The problem is that there is no initial run-in. The lower roller torque is more than the normal running, adding a lot of wear torque. Thus, the combined stress increases and fails. Therefore, should be appropriately bold roll, and pre-emption, can be prevented before the accident.

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

For the upper roll: The problem must be that the pressure of the upper roller is too large, and the strength safety factor of the roller is insufficient. At this time, it is necessary to consider the design to have a relative swing space. The rolling process is carried out step by step and at a reasonable time. For the lower roll: The problem is that there is no initial running in stage. The torque of the lower roller increases a lot of additional wear torque than the normal running in. Therefore, the comprehensive stress increases and the failure occurs. Therefore, the lower roller should be thickened properly and idled in advance to prevent the trouble.

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.