(1) 扇形滤 板脱水孔分布均匀，孔率合理，筋条尺寸大，由高强度工程塑

(1) The fan-shaped filter plate has evenly distributed dewatering holes, reasonable hole rate, large rib size, and is made of high-strength engineering plastics, and the service life is increased by 2-3 times. <br>(2) The filtrate tube has a large number of filters and a large volume of the abdominal cavity of the distribution head, which improves the suction rate and the effect of filtrate discharge. <br>(3) The wear-resistant nylon, single or multi-filament filter cloth makes the cake removal rate high and is not easy to block, and has a long service life. <br>(4) Multi-point dry oil pump centralized multi-point automatic lubrication. <br>(5) The automatic cleaning device of filter cloth keeps its good dehydration effect. <br>(6) Horizontal forced high-speed mixing, rubber and graphite packing at the shaft end and triple seal with water pressure difference without leakage. <br>(7) The stepless speed of the main drive is adjusted according to the concentration and flow rate of the material (AC speed-regulating motor or frequency converter) to achieve the desired working effect. <br>(8) Each plate is composed of 20 fan-shaped plates, which strengthens the filtration process control , Even cake thickness. <br>(9) The friction plate is made of special wear-resistant slab cast iron, which has good rigidity and flexibility, and has a service life of more than ten years. <br>(10) The filtrate pipe is a high-strength wear-resistant ceramic composite steel pipe, which can increase the service life by more than 10 times. <br>(11) Remove the lower flange from the interface between the filtrate pipe and the filter fan, and use the mold positioning to weld directly, reducing the possible air leakage point by 90%. <br>(12) The corundum polymer wear-resistant coating is used in the tank body under the stirring shaft to prevent the tank steel plate from wearing.

(1) Fan filter plate dehydration hole distribution is even, the hole rate is reasonable, the size of the ribs is large, made of high-strength engineering plastic, life increased by 2-3 times.<br>(2) The filter tube has a large filter surface, and the distribution of the head abdominal cavity volume is large, which improves the pumping rate and the effect of the filter discharge.<br>(3) wear-resistant nylon, single or compound filter cloth makes the depie rate high and not easy to clog, long service life.<br>(4) Multi-point dry oil pump concentrated multi-point automatic lubrication.<br>(5) Filter cloth automatic cleaning device, to maintain its good dewatering effect.<br>(6) Horizontal forced high-speed stirring, shaft end using rubber and graphite coil and water pressure difference triple seal without leakage.<br>(7) Main drive stageless variable speed, according to the concentration of the material and flow adjustment (AC speed control motor or inverter) in order to achieve the desired operating effect<br>(8) Each plate consists of 20 pieces of fan-shaped plate, which strengthens the control of the filtration process and makes the cake evenly thick.<br>(9) Friction pieces using special wear-resistant 淜 cast iron just soft seal good, service life of more than 10 years.<br>(10) The filter pipe is a high-strength hard-wearing ceramic composite steel pipe, which increases the life of more than 10 times.<br>(11) The filter pipe and the filter fan interface remove the lower flange, take the mold positioning direct welding, reducing 90% of the possible leakage points.<br>(12) The groove under the mixing shaft is coated with a corundum polymer wear coating to prevent the wear of the groove dwelling steel plate.

(1) The dewatering holes of the fan-shaped filter plate are evenly distributed, with reasonable porosity and large bar size. It is made of high-strength engineering plastics, and its service life is increased by 2-3 times.<br>(2) The filtration number of filtrate pipe is large, and the volume of distribution head and abdominal cavity is large, which improves the air extraction rate and filtrate discharge effect.<br>(3) Wear resistant nylon, single or multifilament filter cloth make the cake removal rate high and not easy to block, with long service life.<br>(4) Multi point dry oil pump centralized multi-point automatic lubrication.<br>(5) The filter cloth automatic cleaning device keeps its good dehydration effect.<br>(6) Horizontal forced high-speed mixing, rubber and graphite packing at the shaft end and triple seal of water pressure difference are adopted to avoid slurry leakage.<br>(7) Stepless speed change of main drive, adjust according to the concentration and flow of materials (AC speed regulating motor or frequency converter), in order to achieve ideal working effect<br>(8) Each plate is composed of 20 sector plates, which strengthen the control of filtration process and make the thickness of cake uniform.<br>(9) The friction plate is made of special wear-resistant cast iron, which is rigid and flexible and has a good sealing performance, with a service life of more than 10 years.<br>(10) The filtrate pipe is a high-strength and wear-resistant ceramic composite steel pipe, which improves the service life by more than 10 times.<br>(11) The lower flange of the interface between the filtrate pipe and the filter fan is removed, and the mold is positioned and welded directly, which reduces the possible air leakage point by 90%.<br>(12) Corundum polymer wear-resistant coating is used in the tank body under the mixing shaft to prevent the tank body steel plate from wearing.<br>