试验室:统一归类摆放,试剂瓶须有明确标示“易燃/有毒”等醒目字样。h.员工进入车间,工作服要三紧(领口紧、袖口紧、下摆紧),凡接触设备的员工的英语翻译

试验室:统一归类摆放,试剂瓶须有明确标示“易燃/有毒”等醒目字样。h.

试验室:统一归类摆放,试剂瓶须有明确标示“易燃/有毒”等醒目字样。h.员工进入车间,工作服要三紧(领口紧、袖口紧、下摆紧),凡接触设备的员工禁止长发露出工作帽外。4.6.3生活安全:提高安防意识a.从自身做起,防止偷盗诈骗,违规事故发生;b.严格遵守宿舍管理制度,如严禁在阳台上嘻笑打闹,禁止集体宿舍男女同宿等;c.财物证件必须要妥善保管,证件与存折要分开保管;d.外出时必须察看抽屉、门窗等有无锁好,携带好备查证件,按交通指示路线行走;e.加强内部团结、杜绝内部矛盾,严禁在厂区内闹事、打架、斗殴。4.6.4交通安全:外出时向同室工友或保安说明自己之去向、目标、路线、回归时间,尽可能结伴同行,严格遵守交通规则,不得跨越栏杆,在车辆中穿梭马路必须遵守红、绿灯规则,紧急情况时应与厂内保安联络,若发生意外时,应速联络当地派出所处理。4.7节约(Save);强化成本意识,养成勤俭节约的好习惯,具体做法如下:4.7.1不铺张浪费,不乱花钱,做到降低耗费,节约资源。4.7.2从思想上树立以厂为家的敬业精神,节约一张纸、一度电、一滴水,从小事做起。4.7.3随时自觉用心,主动考虑节约,降低成本,增加盈余,以达到对公司及员工双盈的效果。4.7.4工作中要严格遵守作息时间,合理安排时间,各岗位应控制人力调配,预防人力过剩。4.7.5在生产中,禁止机台空转,造成不必要的磨损,并定时保养、维护,以延长机台使用寿命。4.7.6爱护公共财物,维护公司财产,不得故意损坏公共财物。4.7.7人离开宿舍应及时切断水源、电源,切勿造成水长流,电长开。5.作业内容5.1定期举行7S培训各部门经理/主管负责本部门的7S培训工作,每月至少举行一次;(可透过早会宣导,广告牌张贴,内部教育等)5.2定期7S巡查(每周一次)7S推行委员会每周组织相关人员对全厂7S执行状况进行检查评比,并公布评比结果5.3主持7S活动 各部门经理/主管主持本部门的7S日常工作,并确保7S活动得到全员有效执行.5.4 稽核记录与统计5.5稽核委员将记录任何不符合现象,并于《7S检查表》评分。同时,各稽核委员将稽核不符合事项E-mail给相关单位主管,并于第二天发出《内部不符合通知单》给相关责任人,跟踪改善结果。5.6对发现之不符合现象,由推行办体系工程师整理于《7S检查不符合事项追踪表》上,该表将发于各相关部门,同时7S执行小组人员将限期追踪以上不符合事项之改善。5.7推行办体系工程师将各区域负责人稽核得分每周统计后登记于各课室《7S评比统计表》,并每月计算出各负责人平均分数。5.8奖惩制度5.8.1 7S推行委员会,根据周评比结果对各部门7S执行情况进行排名.5.8.2每月稽核总分低于80分,区域责任人员进行罚款提报;带“★”项目扣分罚款15元/次。5.8.3每月平均得分最低者:为下月份7S重点改进部门,并给予处罚。5.8.4 每月得分排名第一的区域责任人给予嘉奖提报; 每月得分最后两名给予处罚提报。5.9责任区域的划分按照各部门及各课室技术员责任的机台划分的区域,对责任区域进行检查。由各区域划分主管对负责区域推行效果负全责。各部门须安排人员参加检查;全体人员须共同积极参加。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
4.4.1 In order to clear the air cleanliness of the plant, scheduled monthly dust concentration measured once each project. <br>Determination of place: the center portion of each project, cutting engineering is the core part of the crop. <br>Record: Determination of transition in FIG recording, confirm the change. <br>Activities: clear the dust concentration of the target in order to achieve this target, implementation of the action. <br>In the week after the completion of the measurement plenary session, activity reports, discuss future plans. <br>4.4.2 In order to make the device, the ground, there is no other carrier material dust and dirt must be maintained clean, cleaning. <br>4.4.3 To clean tools after use, usually to keep clean. <br>4.4.4 operation of the product who, subject to maintaining the clean items noted below. <br>① Change gloves regularly to maintain clean. <br>② must specify the hat to wear, the hair should be placed inside the hat. In order not to lose their hair, in the case of long hair you must find a way to tie the hair. <br>③ work clothes are wearing something unusual, to keep it clean. <br>④ shoes to distinguish between indoor and outdoor use, outdoor use not wearing shoes indoors. <br>4.4.5 revealed by the camera, the picture problems, made "7S" billboard, revealed the problem, and to improve and maintain photos, images were compared. <br>※ Annex II: hat, wearing work clothes right photo; ※ Annex III: clothes factory shoe factory wearing cap provisions. <br>4.5 upbringing (Shutsuke): Through a variety of educational and training activities implemented so that everyone abide by the rules of mentality to develop, and willing to comply with various standards and regulations, rather than just follow perfunctory surface, specific practices are as follows: <br>4.5 .1 in charge to correct anytime guide subordinates to conform to order, straighten, sweep, clean, safe, saving the request. <br>4.5.2 encourage mutual supervision among colleagues, to comply with the order, straighten, sweep, clean, safe, saving the request.<br>4.5.3 self-demanding, self-management, between work-related things in line with the order, straighten, sweep, clean, safe, saving the request. <br>4.6 Security (Safety): predict the risk of fire ideas to strengthen and improve accident prevention awareness, compliance with safety regulations, specific practices are as follows: <br>4.6.1 improve the security system, the implementation of safe production responsibility, safety education, prevention, inspection system. <br>4.6.2 workshop production safety: <br>. C absolute prohibition of unauthorized operation of the machine to others, should be promptly cut off the power supply; <br>d before the operation should make voluntary inspection before work: whether the switch button out of control, lights not working, inadequate power supply. short circuit and other undesirable phenomena; <br>. E should be timed operation, to check the products designated absence of abnormality and the like; <br>F to focus on the equipment inspection, inspection interlocking device, a guard or other damage;. <br>G flammable and toxic. after harmful substances (such as alcohol, water that day, degumming water, etc.) must designate a person to keep, and do clearly marked lock control, non- <br>designated personnel shall not be used. <br>Warehouse: must be placed in the red zone and clearly marked. <br>Production line: should not be placed next to the machine, placed in the red zone.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
4.4.1 In order to clarify the cleanliness of the air in the factory, the dust concentration of each project is scheduled to be determined once a month.<br>Measurement site: the central part of each project, cutting engineering is the core of the cutting part.<br>Note: The measurement record is recorded in the passchart to confirm the change.<br>Active: Clear target value of dust concentration, in order to achieve this target value, the implementation of action.<br>Implement plenary meetings and activity reports within one week of the end of the measurement to explore future plans.<br>4.4.2 In order to make the equipment, ground, material rack, etc. free of dust and stains, must maintain cleaning, cleaning.<br>4.4.3 Clean after using the tool, usually keep clean.<br>4.4.4 Persons operating the product shall observe the following maintenance of cleaning matters.<br>(1) Change gloves regularly to maintain cleanliness. (2) Must wear a designated hat, hair should be placed in the hat.<br>In order not to lose hair, long hair must find a way to tighten the hair.<br>(3) The work clothes are the usual things to wear, to keep clean.<br>(4) Shoes should be distinguished from indoor, outdoor use, outdoor shoes can not be worn indoors.<br>4.4.5 By taking pictures, the pictures reveal the problem points, make a "7S" billboard, reveal the problem points, and improve, keep the photos, pictures compared.<br>Annex II: A photo of the correct wearing of a hat and work clothes;<br>4.5 Fostereducation (Shutsuke): Through the implementation of various educational training and activities, everyone is mentally fit to abide by the rules and is willing to comply with various standards and regulations, rather than just superficial perfunctory, as follows:<br>4.5.1 The supervisor corrects the guidance department anytime, anywhere, so that it meets the requirements of finishing, rectifying, cleaning, cleaning, safety and economy.<br>4.5.2 Peer-to-peer supervision and encouragement, so that it meets the requirements of finishing, rectification, cleaning, cleaning, safety, economy.<br>4.5.3 Self-requirement, self-management, between the jobs related things in line with the requirements of finishing, rectification, cleaning, cleaning, safety, saving.<br>4.6 Safety (Safety): Predicting hazards strengthens fire awareness, raises awareness of accidents, and complies with safety regulations as follows:<br>4.6.1 Improve the safety system, implement the responsibility for safe production, safety education, prevention and inspection system.<br>4.6.2 Workshop production safety:<br>c. It is absolutely prohibited to operate other people's machines without authorization, and power should be cut off in time for power failure;<br>d. Before operation should do a good job before the independent inspection: whether the switch button out of control, the light is not good, the power supply is insufficient, the wire short road and other undesirable phenomena;<br>e. The operation should be timed, fixed-point inspection of the production of products for abnormalities, etc.<br>f. The machinery and equipment should be checked in key places, and the linkage device and protective device shall be inspected for damage; <br>g. Flammable and toxic and harmful substances (e.g. alcohol, tiana water, degluing, etc.) must be designated for safekeeping, and clearly marked after lock control, non-<br>Designated persons may not be used.<br>Warehouse: Must be placed in a red area and clearly marked. Line: Do not place next to the machine, placed in the red area.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
4.4.1 in order to determine the cleanliness of the air in the factory, it is scheduled to measure the dust concentration of each project once a month.<br>Testing place: the center of each project and cutting project are the core of cutting part.<br>Record: measure and record in the process chart to confirm the change.<br>Activity: define the target value of dust concentration. In order to achieve the target value, carry out actions.<br>Carry out the plenary meeting and activity report within one week after the end of measurement, and discuss the future plan.<br>4.4.2 in order to make the equipment, ground, material frame, etc. free of dust and stains, it is necessary to maintain cleaning.<br>4.4.3 clean the tools after use and keep them clean normally.<br>4.4.4 the operator of the product shall comply with the following cleaning matters.<br>① change gloves regularly to keep them clean.<br>② the specified hat must be worn, and the hair shall be put in the hat. In order not to lose your hair, you must find a way to tie it tightly when you have long hair.<br>③ work clothes are things that are usually worn, and they should be kept clean.<br>④ the shoes shall be used indoors and outdoors. The shoes for outdoor use shall not be worn indoors.<br>4.4.5 reveal the problem points by taking photos and pictures, make "7S" billboard, reveal the problem points, improve and keep the photos and pictures for comparison.<br>* attachment 2: photos of correct wearing of hats and work clothes; * attachment 3: wearing regulations of factory shoes and hats.<br>4.5 shutsuke: through various kinds of education, training and activities, everyone is able to form a mindset to abide by the rules, and is willing to abide by various standards and regulations, rather than just superficial compliance. The specific methods are as follows:<br>4.5.1 the supervisor shall correct and guide the subordinates at any time and place to make them meet the requirements of sorting, rectification, cleaning, safety and economy.<br>4.5.2 colleagues shall supervise and encourage each other to meet the requirements of sorting, rectification, cleaning, safety and economy.<br>4.5.3 self requirements, self-management, and relevant matters between posts meet the requirements of sorting, rectification, cleaning, safety and economy.<br>4.6 safety: predict the danger, strengthen the concept of fire protection, improve the awareness of accident prevention, and abide by the safety regulations. The specific methods are as follows:<br>4.6.1 improve safety system, implement safety production responsibility, safety education, prevention and inspection system.<br>4.6.2 workshop production safety:<br>C. It is absolutely forbidden to operate other machines without permission, and the power supply shall be cut off in time in case of power failure;<br>D. conduct self inspection before operation: check whether there is any out of control switch button, ineffective indicator light, insufficient power supply, short circuit of wires and other adverse phenomena;<br>E. during the operation, it is necessary to regularly and regularly check whether the products produced are abnormal, etc.<br>F. focus on the inspection of machinery and equipment, and check whether the linkage device and protective device are damaged;<br>G. inflammable and toxic and harmful substances (such as alcohol, Tianna water, degumming water, etc.) must be kept by specially assigned person, and locked after being clearly marked.<br>Designated personnel shall not use.<br>Warehouse: must be placed in a red area and clearly marked.<br>Production line: it shall not be placed next to the machine, but in the red area.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: