在手动状态下,将开关拔到相应的方向并保持可控制上行、下行、左行和右行(调速器调整速度),松开动作立即停止。注意:只有工作台达到水平状态磨盘才的英语翻译

在手动状态下,将开关拔到相应的方向并保持可控制上行、下行、左行和右行(

在手动状态下,将开关拔到相应的方向并保持可控制上行、下行、左行和右行(调速器调整速度),松开动作立即停止。注意:只有工作台达到水平状态磨盘才能运行,否则会造成机械损坏。磨盘加压/减压选择开关:在任意状态下,将开关拔到相应的方向可控制磨盘(向下)加压或(向上)减压动作。复位按钮:当机器未处于初始位时按下此按钮机械会自动回位。本机初始位置是磨头装置处于上限位、机头处于左限位、横梁处于前限位。注意:复位按钮只在磨盘主机未启动有效。压力表:压缩空气压力显示。横梁前行/后行开关:未自动工作时向左/向右拨动本开关选择横梁向前或向后行走,直至将开关置于中间位停止。若未将开关置于中间位置当横梁移动到前限位或后限位时机械也会停止。压力调节器:拔出顺时针旋转调大磨盘加压压力,逆时针旋转调小磨盘加压压力。电流表:显示本机工作电流。磨盘旋转启动按钮:按下该按钮磨盘启动旋转。磨盘旋转停止按钮:按下该按钮磨盘停止旋转。磨盘旋转调速旋钮:启动磨盘后,顺时针旋转该旋钮,磨盘旋转速度加快;逆时针旋转该旋钮磨盘旋转速度变慢。注意:调节磨盘转速时要慢慢转动该旋钮,严禁快速旋转,否则可能造成变频器故障甚至损坏。左右行走调速旋钮:向左或向右行走时,顺时针旋转该旋钮,向左/向右行走速度加快;逆时针旋转该旋钮,向左/向右行走速度变慢。注意:调节左右行走速度时,要慢慢转动该旋钮,严禁快速旋转进行速度调节,否则可能造成变频器跳故障甚至损坏。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
In the manual state, pull the switch to the corresponding direction and keep it controllable up, down, left and right (speed governor adjusts the speed), release the action and stop immediately. <br><br>Note: The grinding disc can only be operated when the workbench reaches the level state, otherwise it will cause mechanical damage. <br><br>Grinding plate pressurization/decompression selection switch: In any state, pull the switch to the corresponding direction to control the grinding plate (downward) pressurization or (upward) decompression action. <br><br>Reset button: <br>When the machine is not in the initial position, press this button and the machine will automatically return. <br>The initial position of the machine is that the grinding head device is at the upper limit, the head is at the left limit, and the beam is at the front limit. <br><br>Note: The reset button is only valid when the grinding disc host is not started. <br><br>Pressure gauge: display of compressed air pressure. <br><br>Cross beam forward/backward switch: When it is not working automatically, turn this switch to the left/right to select the beam to move forward or backward until the switch is placed in the middle position to stop. <br><br>If the switch is not placed in the middle position, the machine will stop when the beam moves to the front limit or the rear limit. <br>Pressure regulator: Pull out the clockwise rotation to increase the pressure of the grinding disc, and turn it counterclockwise to reduce the pressure of the grinding disc. <br>Ammeter: Display the working current of the machine. <br>Grinding disc rotation start button: Press this button to start grinding disc rotation. <br>Grinding disc rotation stop button: Press this button to stop the grinding disc rotating. <br>Grinding disc rotation speed control knob: After starting the grinding disc, turn the knob clockwise to increase the rotation speed of the grinding disc; turn the knob counterclockwise to slow down the rotation speed of the grinding disc. <br>Note: When adjusting the speed of the grinding disc, turn the knob slowly, and it is strictly prohibited to rotate it quickly, otherwise it may cause the inverter to malfunction or even be damaged. <br>Left and right walking speed control knob: When walking left or right, turn the knob clockwise to speed up the walking left/right; turn the knob counterclockwise to slow down the walking speed to the left/right. <br>Note: When adjusting the left and right walking speed, turn the knob slowly. It is strictly forbidden to rotate the speed quickly to adjust the speed, otherwise it may cause the inverter to trip or even be damaged.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
In the manual state, unplug the switch in the appropriate direction and maintain control of the up, down, left, and right (timer adjustment speed), and the release action stops immediately.<br><br>Note: Only the workstation reaches the horizontal state grinding disc to operate, otherwise it will cause mechanical damage.<br><br>Grinding disc pressurized/decompression selection switch: In any state, pull the switch in the appropriate direction to control the grinding disc (down) pressurized or (up) decompression action.<br><br>Reset button:<br>Pressing this button automatically returns when the machine is not in the initial position.<br>The initial position of the machine is that the grinding head unit is in the upper limit, the head is in the left limit and the beam is in the front limit.<br><br>Note: The reset button is only valid if the grinding disc host does not start.<br><br>Pressure meter: Compressed air pressure display.<br><br>Beam forward/back switch: Do not automatically work to move this switch left/right To select the beam to walk forward or back until the switch is placed in the middle position to stop.<br><br>The machine also stops if the switch is not placed in the middle position when the beam moves to the front or rear limits.<br>Pressure regulator: pull out the clockwise rotation of the large grinding disc pressure pressure, counterclockwise rotation of the small grinding plate pressure pressure.<br>Current meter: Displays the current of the machine.<br>Grinding disc rotation start button: Press the button grinding disc to start rotation.<br>Grinding disc rotation stop button: Press the button grinding disc to stop rotating.<br>Grinding disc rotation speed dial: After starting the grinding disc, turn the knob clockwise, the grinding disc rotation speed is accelerated, counterclockwise rotation of the knob grinding disc rotation speed is slower.<br>Note: When adjusting the grinding disc speed, slowly turn the knob, do not rotate quickly, otherwise it may cause transmission failure or even damage.<br>Walk the speed knob left or right: When you walk left or right, turn the knob clockwise, walk faster left/right, turn the knob counterclockwise, and walk slowly left/right.<br>Note: When adjusting the left and right walking speed, to slowly turn the knob, do not quickly rotate for speed adjustment, otherwise it may cause the drive jump failure or even damage.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
In the manual state, pull the switch to the corresponding direction and keep it to control the up, down, left and right travel (the governor adjusts the speed), and the release action will stop immediately.<br>Note: only when the table reaches the horizontal state, the grinding plate can run, otherwise it will cause mechanical damage.<br>Disc pressure / pressure reduction selection switch: in any state, pull the switch to the corresponding direction to control the grinding plate (downward) pressure or (up) pressure reduction action.<br>Reset button:<br>When the machine is not in the initial position, press this button and the machine will return automatically.<br>The initial position of the machine is that the grinding head device is in the upper limit position, the machine head is in the left limit position, and the beam is in the front limit position.<br>Note: the reset button is only valid when the grinding disc host is not started.<br>Pressure gauge: compressed air pressure display.<br>Beam forward / backward switch: when the switch is not working automatically, move the switch to the left / right to select the beam to move forward or backward until the switch is set to the middle position to stop.<br>If the switch is not in the middle position, the machine will stop when the beam moves to the front limit or the rear limit.<br>Pressure regulator: pull out and rotate clockwise to increase the pressure of the grinding plate, and counter clockwise to decrease the pressure of the grinding plate.<br>Ammeter: display the working current of the machine.<br>Grinding disc rotation start button: press this button to start the rotation of grinding disc.<br>Grinding disc rotation stop button: press this button to stop the rotation of grinding disc.<br>Rotating speed control knob of grinding plate: after starting the grinding plate, rotating the knob clockwise will accelerate the rotation speed of grinding plate; turning the knob anticlockwise will slow down the rotation speed of grinding plate.<br>Note: when adjusting the speed of the grinding disc, slowly turn the knob, and it is strictly prohibited to rotate it rapidly, otherwise, the inverter may be damaged.<br>Left and right travel speed control knob: when walking to the left or right, rotate the knob clockwise to speed up the left / right travel speed; when turning the knob anticlockwise, the left / right travel speed becomes slow.<br>Note: when adjusting the left and right walking speed, turn the knob slowly. It is strictly forbidden to rotate the knob quickly to adjust the speed. Otherwise, the frequency converter may jump or even be damaged.
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: