折弯长或大工件时,需要两人以上协同工作。避免由于工件受力变形时的倾倒。工人不准近距离手扶被压的工件。校正或压制工件时,操作员应将工件置于模具的英语翻译

折弯长或大工件时,需要两人以上协同工作。避免由于工件受力变形时的倾倒。

折弯长或大工件时,需要两人以上协同工作。避免由于工件受力变形时的倾倒。工人不准近距离手扶被压的工件。校正或压制工件时,操作员应将工件置于模具的中间位置,不准偏压。上模要慢慢接近工件,防止工件受力迸出。工作中需要经常检查两个油缸的行程是否一致。遇到问题,请及时调整或报修。发现油缸活塞抖动或油泵发出噪音时,必须排出油路中的空气。要经常注意油箱,观察油面是否合适。如油面过高,需检查回油管路,调节回油阀门。严禁溢出油箱。保持工作油温度≤45℃。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
When bending long or large workpieces, two or more people are required to work together. <br>Avoid toppling when the workpiece is deformed by force. <br>Workers are not allowed to hold the pressed workpiece at close range. <br>When calibrating or pressing the workpiece, the operator should place the workpiece in the middle of the mold without biasing. <br>The upper die should approach the workpiece slowly to prevent the workpiece from being forced out. <br>It is necessary to check whether the strokes of the two cylinders are consistent during work. If you encounter any problems, please adjust or report for repair in time. <br>When the oil cylinder piston is shaken or the oil pump makes noise, the air in the oil circuit must be discharged. <br>Always pay attention to the fuel tank and observe whether the oil level is suitable. <br>If the oil level is too high, check the oil return line and adjust the oil return valve. It is strictly forbidden to overflow the fuel tank. Keep working oil temperature ≤45℃.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
When bending long or large work pieces, more than two people are required to work together.<br>Avoid dumping when deformed due to force on the work piece.<br>Workers are not allowed to hold the pressed work pieces up close.<br>When correcting or pressing the work piece, the operator should place the work piece in the middle of the mold and not allow bias.<br>The upper mold should slowly approach the work piece to prevent the work piece from being forced out.<br>The travel of the two cylinders needs to be checked frequently during work. If you encounter problems, please adjust or report them in time.<br>Air in the oil path must be drained when cylinder piston shakes or when noise from the oil pump is detected.<br>Always pay attention to the tank and observe if the oil surface is suitable.<br>If the oil surface is too high, check the return line and adjust the return valve. Do not spill the fuel tank. Keep the operating oil temperature ≤ 45 degrees C.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
When bending long or large workpieces, more than two people are required to work together.<br>Avoid toppling due to deformation of workpiece.<br>Workers are not allowed to hold the pressed workpiece close to each other.<br>When correcting or pressing the workpiece, the operator should place the workpiece in the middle of the mold, and bias is not allowed.<br>The upper die should be slowly close to the workpiece to prevent the workpiece from bursting out under stress.<br>It is necessary to check whether the stroke of the two cylinders is consistent. In case of any problem, please adjust or repair it in time.<br>When the oil cylinder piston vibrates or the oil pump makes noise, the air in the oil circuit must be discharged.<br>Always pay attention to the oil tank and observe whether the oil level is suitable.<br>If the oil level is too high, check the oil return pipeline and adjust the oil return valve. Do not overflow the tank. Keep the working oil temperature ≤ 45 ℃.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: