阿布扎比塔维勒海水淡化项目 PAM泡药机摩洛哥杰拉达运维项目部 第七册

Abu Dhabi <br>Tavel Seawater Desalination Project PAM Medicine Bubble Machine, Moroccan Gerada Operation and Maintenance Project Department Volume 7 Chemical Professional Operation Regulations <br>Page Total Page <br>Abu Dhabi Tawelle <br>Seawater Desalination Project <br>PAM Medicine Bubble Machine <br>Operation Guide <br>1, Overview <br>2. Technical parameters <br>3. Safety precautions for safety measures <br>4. Operation and operation <br>5. Cleaning treatment <br>6. Failure treatment <br>7. Equipment structure drawing and P&D diagram <br>8. Alarm <br>9. Preventive maintenance <br>10. Periodic maintenance <br>1.1 Project introduction: <br>This project adopts The 100% reverse osmosis desalination technology (SWRO) ensures that the water output of the whole plant is 200 MIGD. <br>The water plant mainly includes water intake system, pretreatment system (DAF and DMGF), RO reverse osmosis system, capacity recovery device, post-treatment system, wastewater treatment system, compressed air system, fire protection HVAC, dosing system, water storage tank area, GIS, electrical system, thermal control system and measurement system, etc. <br>In addition, this project also includes the transformation of the opposite side booster station and photovoltaic power generation. Among them, PV photovoltaic is divided into Basic PV and Auxiliary PV, which can reduce the specific power consumption of water production through PV photovoltaic power generation. <br>1.2 Purpose: <br>PAM is a linear organic polymer, and also a polymer water treatment flocculant product. It can absorb suspended particles in water and act as a link and bridging between particles, so that fine particles can be compared. Large flocs, and accelerate the speed of precipitation. <br>This process is called flocculation, because of its good flocculation effect, PAM is used as a flocculant in water treatment and is widely used in sewage treatment.<br>After the equipment fails, the on-site personnel can perform maintenance or replacement in accordance with the OM instruction manual to achieve the ability of the equipment to resume operation. <br>Processing capacity: Q=6.0m3/h, <br>dry powder dosage: 28kg/h <br>solution concentration: 0.3-0.5% <br>body material: PP <br>hopper: SS316 <br>feeding conveyor: SS316 <br>mixing shaft and blade: SS316 <br>electric control box: <br>pipe fittings : UPVC <br>electrical components: Schneider/Siemens <br>2.1 Principle: <br>Dry powder medicament enters the premixer from the lower part of the hopper for premixing with clean water, and the wetted material enters the preparation tank for dilution and mixing, and then passes through the maturing tank for maturation and then enters storage groove. <br>When the liquid level of the storage tank reaches a high level, the configuration process is automatically stopped, and when the solution drops to a low level, the configuration process is automatically started. <br>The configuration flow and concentration can be controlled by adjusting the inlet water flow and the conveyor speed. <br>2.2 Process flow: <br>PAM automatic infusion machine is composed of water supply system (pipes and valves, etc.), dry powder dosing system, integrated three-tank combined box, mixing system, automatic control and detection system. <br>3.1 The system has dangerous points: In the <br>dry powder dosing system, the material propeller is conveyed forward by the spiral blade rotation, and must be ensured to stop rotating during maintenance; in the <br>mixing system, the motor drives the mixing shaft and the mixing impeller to rotate. Be sure to stop rotating during maintenance. <br>3.2 Safety protection measures: In <br>order to ensure the long-term stable operation of the PAM infusion device, the following safety protections should be done: <br>3.2.1 After the equipment is put into operation, check whether the circuit and control cabinet are damaged, the environment is reliable, and whether the equipment is grounded or connected to zero. , Is the facility safe? <br>If unfavorable conditions are found, protective measures should be taken in time;<br>3.2.2 The operator should wear labor protection equipment during <br>operation. 3.2.3 The operator shall not disassemble the equipment at will. <br>3.2.4 When maintaining, maintaining, repairing and cleaning the equipment, make sure that the equipment is turned off and cut off the power completely. <br>At the same time, warning signs should be placed at a conspicuous position on the work site to indicate that the equipment is under maintenance or repair, or that someone is working on site. <br>3.2.5 When the equipment is in operation, it is strictly prohibited to adjust, measure, lubricate, remove debris, or wipe the equipment by hand. <br>3.2.6 After the maintenance work is completed, thoroughly check whether there are tools or objects left in the equipment, and clean up the workplace and equipment sanitation. <br>3.2.7 Understand the preventive measures and operating procedures in detail before repairs, maintenance or repairs. <br>Workers must concentrate their thoughts, wear protective equipment, and stand in a safe position. <br>3.2.8 Appropriate disassembly tools should be used when repairing, maintaining or repairing equipment, and knocking and disassembly are strictly prohibited. <br>3.2.9 It is strictly forbidden to wipe the equipment with flammable and explosive materials. <br>Do not place tarpaulins on the equipment, and do not store flammable or explosive materials around the equipment. <br>3.2.10 Add dry powder to this equipment. <br>The equipment is well ventilated and open flames are strictly prohibited. <br>3.2.11 Use even force when opening and closing each valve, especially when operating UPVC plastic valves. <br>3.2.12 When the power is turned on again after a sudden power failure, the previous operating state can be automatically restored. <br>3.2.13 If foreign matter is found in the flowmeter, try to remove it in time, and it is not allowed to knock the flowmeter; when the rotor flowmeter is not clearly indicated, it should be removed and washed with 5%-10% dilute hydrochloric acid, and pay attention to safety.

PAM foammachine for the Tawile desalination project in Abu Dhabi.<br>Volume VII, Department of Operations projects in Jerrada, Morocco.<br>Page Total.<br>Abu Davier Abu Dhabi.<br>Desalination project.<br>PAM foam machine.<br>Run the guidebook.<br>1, an overview.<br>2, technical parameters.<br>3, security measures security notes.<br>4, run the operation.<br>5, cleaning treatment.<br>6, fault management.<br>7, equipment construction map and P-D diagram.<br>8, alarm.<br>9, preventive maintenance.<br>10, regular maintenance.<br>1.1 Introduction to the project:<br>This project uses 100% reverse osmosis desalination technology (SWRO) to ensure that the entire plant's water production capacity of 200 MIGD.<br>The water plant mainly includes water collection systems, pretreatment systems (DAF and DMGF), RO reverse osmosis systems, capacity recovery devices, retreatment systems, wastewater treatment systems, compressed air systems, fire-fighting heating systems, drug supply systems, water storage tanks, GIS, electrical systems, thermal control systems and measurement systems.<br>In addition, the project also includes side boost station transformation, photovoltaic power generation, including PV photovoltaic scored as Basic PV and Auxiliary PV, through PV photovoltaic power generation to achieve a reduction in water production than electricity consumption.<br>1.2 Purpose:<br>PAM is a linear organic polymer polymer, but also a polymer water treatment flocculant products, can adsorb the suspended particles in the water, in the particles between the link bridge, so that fine particles form a relatively large floc, and speed up the rate of precipitation.<br>This process is called flocculation, because of which the good flocculation effect PAM as a flocculation agent for water treatment and is widely used in sewage treatment.<br>In the event of a failure of the equipment, field personnel are able to follow the OM instruction manual for service or replacement in order to achieve the ability of the equipment to resume operation.<br>Processing capacity: Q- 6.0m3/h,<br>Dry powder cast plus: 28kg/h.<br>Solution concentration: 0.3-0.5%<br>Body material: PP.<br>Hopper: SS316.<br>Feed conveyor: SS316.<br>Stirring shaft and blades: SS316.<br>Electronic control box:<br>Pipe accessories: UPVC.<br>Electrical components: Schneider/Siemens.<br>2.1 Principle:<br>The dry powder agent enters the premixer and water premix from the spiral thruster at the lower part of the hopper, is diluted and mixed by wet material into the preparation tank, and then the cooked tank enters the storage tank.<br>When the storage tank level reaches a high level, the configuration process stops automatically and starts the configuration process automatically when the solution drops to the low level.<br>The configuration flow and concentration can be controlled by adjusting the inlet flow and conveyor speed.<br>2.2 Process:<br>PAM automatic foam machine consists of water supply system (pipes and valves, etc.), dry powder feeding system, integrated three-slot combination box, mixing system, automatic control and testing system.<br>3.1 There are danger points in the system:<br>In the dry powder feeding system, the material thruster is driven forward by the spiral rotation, and it is necessary to ensure that it stops rotating during maintenance;<br>In the mixing system, the motor drives the stirring shaft and the stirring impeller rotates, making sure it stops turning during maintenance.<br>3.2 Safety measures:<br>In order to ensure the long-term stable operation of THE PAM foaming device, the following safety protection should be done:<br>3.2.1 After the equipment is put into operation, it is safe to check the line, control cabinet for damage, whether the environment is reliable, whether the equipment is grounded or grounded, and the facility is safe.<br>If adverse situations are found, protective measures should be taken in a timely manner;<br>3.2.2 Operators should wear labor protection when operating.<br>3.2.3 The operator shall not disassemble the equipment at will.<br>3.2.4 When maintaining, maintaining, repairing and cleaning equipment, confirm that the equipment is turned off and completely cut off the power supply.<br>At the same time, a prominent place at the work site should be placed with a warning sign indicating that the equipment is in a maintenance or repair state or that someone is working on site.<br>3.2.5 When the equipment is running, it is strictly forbidden to adjust, measure, lubricate, remove debris and wipe the equipment by hand.<br>3.2.6 After the completion of the repair work, the equipment should be thoroughly checked for tools or items, and the workplace and equipment hygiene should be cleaned.<br>3.2.7 Learn more about preventive measures and operating procedures prior to repair, maintenance or repair.<br>Staff must focus their minds, wear protective gear and be in a safe position.<br>3.2.8 Proper removal tools should be used when repairing, maintaining or repairing equipment, and knocking and removal should be strictly prohibited.<br>3.2.9 It is strictly forbidden to wipe equipment with inflammable and explosive articles.<br>No tarpaulins shall be placed on the equipment, and inflammable and explosive articles shall not be stored around the equipment.<br>3.2.10 Add dry powder to this device.<br>The equipment is well ventilated around, and open flames are strictly prohibited.<br>3.2.11 when turning on and off the valves, the force should be uniform, especially when operating UPVC plastic valves can not be too strong.<br>3.2.12 When a sudden power outage is followed and a call is made, it is possible to automatically resume the previous operating state.<br>3.2.13 If a foreign object is found in the flow meter, it should be tried to eliminate it in time and not allow the clicking flow meter, and when the rotor flow meter is not clearly indicated, it should be removed with 5% to 10% thin hydrochloric acid wash, and pay attention to safety.

PAM soaking machine for tavile seawater desalination project in Abu Dhabi<br>Operation and maintenance project Department of gerada, Morocco Volume VII operation procedures for chemical specialty<br>Page of<br>Tavile, Abu Dhabi<br>Desalination project<br>PAM soaking machine<br>Operation instruction manual<br>1. Overview<br>2. Technical parameters<br>3. Safety measures safety instructions<br>4. Run operation<br>5. Cleaning treatment<br>6. Troubleshooting<br>7. Equipment construction drawing and P & D drawing<br>8. Call the police<br>9. Preventive maintenance<br>10. Regular maintenance<br>1.1 project introduction:<br>The project adopts 100% reverse osmosis seawater desalination technology (SWRO) to ensure that the water production capacity of the whole plant is 200 MIGD.<br>The water plant mainly includes water intake system, pretreatment system (DAF and dmgf), RO reverse osmosis system, capacity recovery device, post-treatment system, wastewater treatment system, compressed air system, fire-fighting heating and ventilation, dosing system, water storage tank area, GIS, electrical system, thermal control system and measurement system.<br>In addition, the project also includes the transformation of the opposite booster station, photovoltaic power generation, etc., in which PV photovoltaic is divided into basic PV and auxiliary PV, through which the specific power consumption of water production can be reduced.<br>1.2 purpose:<br>PAM is a kind of linear organic polymer, and it is also a kind of polymer flocculant for water treatment. It can adsorb the suspended particles in water and act as a bridge between the particles, so that the fine particles form larger flocs and accelerate the sedimentation rate.<br>This process is called flocculation, because of its good flocculation effect, PAM is widely used in wastewater treatment as a flocculant.<br>After the equipment fails, the on-site personnel can carry out maintenance or replacement according to OM instruction manual, so as to achieve the ability of equipment recovery.<br>Treatment capacity: q = 6.0m3/h,<br>Dry powder dosage: 28KG / h<br>Solution concentration: 0.3-0.5%<br>Body material: PP<br>Hopper: SS316<br>Feeding conveyor: SS316<br>Mixing shaft and blade: SS316<br>Electric control panel:<br>Pipe fittings: UPVC<br>Electrical components: Schneider / Siemens<br>2.1 principle:<br>The dry powder agent enters the premixer from the screw propeller at the lower part of the hopper and premixes with clean water. The wet material enters the preparation tank for dilution and mixing, and then goes through the curing tank for aging and then enters the storage tank.<br>When the liquid level of the storage tank reaches a high level, the configuration process automatically stops, and when the solution drops to the low level, the configuration process is automatically started.<br>The configuration flow and concentration can be controlled by adjusting the inflow flow and conveyor speed.<br>2.2 process flow:<br>PAM automatic soaking machine is composed of water supply system (composed of pipes and valves), dry powder feeding system, integrated three tank combined box, mixing system, automatic control and detection system.<br>3.1 there are dangerous points in the system<br>In the dry powder feeding system, the material propeller is transported forward by the spiral vane rotating belt, so it must be ensured to stop rotating during maintenance;<br>In the mixing system, the motor drives the mixing shaft and impeller to rotate, so it must be ensured to stop rotating during maintenance.<br>3.2 safety protection measures:<br>In order to ensure the long-term stable operation of PAM foam device, the following safety protection measures should be taken:<br>3.2.1 after the equipment is put into operation, check whether the line and control cabinet are damaged, whether the environment is reliable, whether the equipment is grounded or connected to zero, and whether the facilities are safe.<br>In case of any adverse situation, protective measures shall be taken in time;<br>3.2.2 operators shall wear labor protection articles during operation<br>3.2.3 the operator shall not dismantle the equipment at will<br>3.2.4 during the maintenance, maintenance, repair and cleaning of the equipment, make sure that the equipment is in the shutdown state and completely cut off the power supply.<br>At the same time, warning signs should be placed in a conspicuous position on the work site to indicate that the equipment is in maintenance or repair status, or that someone is working on the site.<br>3.2.5 when the equipment is in operation, it is strictly forbidden to adjust, measure, lubricate, remove impurities and wipe the equipment by hand.<br>3.2.6 after the maintenance work, thoroughly check whether there are tools or articles left in the equipment, and clean the workplace and equipment.<br>3.2.7 understand the preventive measures and operation procedures in detail before repair, maintenance or repair.<br>The staff must concentrate, wear protective equipment and stand in a safe position.<br>3.2.8 when repairing, maintaining or repairing the equipment, proper disassembly tools shall be used, and knocking and dismantling are strictly prohibited.<br>3.2.9 it is strictly forbidden to wipe equipment with inflammable and explosive materials.<br>No oilcloth shall be placed on the equipment, and inflammable and explosive materials shall be stored around the equipment.<br>3.2.10 add dry powder to the equipment.<br>The equipment is well ventilated and no open fire is allowed.<br>3.2.11 the force shall be uniform when opening and closing each valve, especially when operating the UPVC Plastic valve.<br>3.2.12 in case of power failure and power supply, it can automatically restore the previous operation state.<br>3.2.13 if foreign matters are found in the flowmeter, they shall be removed in time, and it is not allowed to knock the flowmeter; when the indication of the rotameter is not clear, it shall be removed and washed with 5% - 10% dilute hydrochloric acid, and attention shall be paid to safety.<br>