保护膜的透明性及选型要求保护膜在进行使用的过程中,其涂胶膜粘着剂的种类有溶剂型橡胶粘着剂、溶剂型丙烯酸粘着剂、水性丙烯酸粘着剂、以及硅酮粘着的英语翻译

保护膜的透明性及选型要求保护膜在进行使用的过程中,其涂胶膜粘着剂的种类

保护膜的透明性及选型要求保护膜在进行使用的过程中,其涂胶膜粘着剂的种类有溶剂型橡胶粘着剂、溶剂型丙烯酸粘着剂、水性丙烯酸粘着剂、以及硅酮粘着剂。其中又以水性丙烯酸粘着剂是普遍应用此类产品,它可容易调整粘着力,并且透明性和耐候性佳。保护膜一般是以共挤的方式生产,而其自粘层一般为EVA、超低密度聚乙烯或聚烯烃塑性体树脂为主,此种结构形式亦渐渐成为市场的主流,因为它较涂胶膜具有较多的优点,如无残胶、提供稳定的粘着力、降低使用者成本以及对保护膜制造商创造较高利润。保护膜首先要在显示器关机的情况下看,方法同上,把各款保护膜依次贴开后,越显屏幕底色的其雾度越小,雾度越小的说明材质越好,此法如果用黑色的测试板则更容易看出差异。保护膜还有一种方法是在稍暗的室内,开一支日光灯,把保护膜撕除上下离形膜后用手拿住放在眼睛与灯光之间,你仔细看是否有一层雾状的东西在保护膜内均匀分布,那是影响雾度的祸首,这种雾状的东西越严重,说明雾度越大,材料越差,反之说明越好,(注意雾度会影 响透度率,但与透过率是两个不同的概念!)保护膜由于液晶显示器是敏感器件怕静电,在贴保护膜时静电越小越好,测试方法是准备好待测试的保护膜(3层料或两层料),抽一支烟敲点烟灰在桌面,或是弄点细小的纸屑在桌面,然后撕去保护膜的上面一层保护膜(针对3层料有此一步骤),再撕带硅胶这层的保护膜,撕掉这层保护膜时立即将使用层(硅胶面)去靠近烟灰或纸屑,看保护膜是否会将这些东西吸附到保护膜的硅胶层上,吸附程度是否强烈。越是强烈则说明此材料产生的静电越高材料越差,反之则越好。保护膜的选型1、不同的表面需要不同的粘性;2、同样相似的表面不同的材料也可能需要不同的粘性;3、后续的加工步骤则是决定粘性的关键。后续加工一般有弯曲、冲压、裁切、钻孔、热成型等;4、厚度与粘性的合理搭配;5、保护膜的拉伸强度和伸长率,以确保保护膜的柔韧性和强度能达到要求;6、保护膜选型的原则:充分测试。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
The transparency and selection of the <br>protective film require that the protective film adhesives include solvent-based rubber adhesives, solvent-based acrylic adhesives, water-based acrylic adhesives, and silicone adhesives during the use of the protective film. Among them, water-based acrylic adhesives are commonly used in such products, which can easily adjust the adhesion, and have good transparency and weather resistance. <br>The protective film is generally produced by co-extrusion, and the self-adhesive layer is generally dominated by EVA, ultra-low density polyethylene or polyolefin plastomer resin, and this structure form has gradually become the mainstream of the market because it is more glued The film has many advantages, such as no residual glue, provides stable adhesion, reduces user costs, and creates higher profits for protective film manufacturers. <br>The protective film must first be viewed when the display is turned off. The method is the same as above. After attaching each protective film in sequence, the more the background color of the screen is, the smaller the haze is. The smaller the haze is, the better the material is. It is easier to see the difference with the black test board. <br>Another way to protect the film is to turn on a fluorescent lamp in a slightly dark room, remove the protective film from the upper and lower release films, hold it between your eyes and the light with your hands, and carefully see if there is a layer of fog Evenly distributed in the protective film, it is the culprit that affects the haze. The more serious this kind of fog, the greater the haze, the worse the material, and the better the contrary, (note that haze will affect the permeability rate, but Transmittance is two different concepts!) <br>Protective film Since the liquid crystal display is a sensitive device that is afraid of static electricity, the smaller the static electricity when the protective film is attached, the better. The test method is to prepare the protective film to be tested (3 layers or two Layer material), smoke a cigarette, tap some soot on the table, or get some small paper scraps on the table, then tear off the protective film above the protective film (this step is for 3 layers of material), and then tear the tape Silicone protective film. When tearing off this protective film, immediately use the layer (silicone surface) close to soot or paper dust to see if the protective film will adsorb these things on the silicone layer of the protective film. . The stronger it is, the higher the static electricity generated by this material is, the worse the material is, and the better the opposite. <br>Selection of protective film <br>1. Different surfaces require different viscosities; <br>2. Different materials with the same similar surfaces may also require different viscosities;<br>3. The subsequent processing steps are the key to determining the viscosity. Subsequent processing generally includes bending, stamping, cutting, drilling, thermoforming, etc .; <br>4. Reasonable matching of thickness and viscosity; <br>5. The tensile strength and elongation of the protective film to ensure that the flexibility and strength of the protective film can reach Requirements; <br>6. Principle of selection of protective film: full test.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
Transparency and selection requirements for protective film<br>In the process of use of the protective film, the types of adhesive adhesives are solvent-based rubber adhesives, solvent-based acrylic adhesives, water-based acrylic adhesives, and silicone adhesives. In addition to the water-based acrylic adhesive is widely used in such products, it can easily adjust the adhesive, and transparency and weather resistance is good.<br>Protective film is generally produced in a co-squeezing manner, and its self-adhesive layer is generally EVA, ultra-low density polyethylene or polyolefin plastic body resin-based, this form of structure has gradually become the mainstream of the market, because it has more advantages than the coating film, such as no residual glue, provide stable adhesive, reduce user costs and create higher profits for the manufacturer of protective film.<br>The protective film first in the case of monitor shutdown, the method is the same, the protection film in turn after the release, the more the screen color of its fog is smaller, the smaller the fog, the better the description material, this method if the black test board is easier to see the difference.<br>There is also a way to protect the film is in a slightly darker room, open a fluorescent light, the protective film to tear off the upper and lower off the film hand to hold between the eyes and the light, you carefully see whether there is a layer of fog in the protective film evenly distributed, that is the impact of fog, the more serious the fog, the more serious the fog, the worse the material, the worse, (attention fog will affect the transmission rate, but with the two different concepts!<br>Protection film because the liquid crystal display is sensitive device afraid of static electricity, when the protective film static smaller the better, the test method is ready to be tested protective film (3 layers or two layers of material), smoke a cigarette to knock a cigarette ash on the desktop, or make a small piece of confetti on the desktop And then tear off the protective film above the protective film (for 3 layers of material has this step), and then tear the protective film with silicone layer, tear off this layer of protective film immediately will use the layer (silicone surface) to get close to soot or confetti, See if the protective film will adsorbed these things to the silicone layer of the protective film, the degree of adsorption is strong. The stronger the material, the higher the static electricity produced by the material, the worse the material, the better.<br>Selection of protective films<br>1, different surfaces need different viscosity;<br>2. Similar surface different materials may also need different viscosity;<br>3, the follow-up processing steps are the key to determine the stickiness. Follow-up processing generally has bending, stamping, cutting, drilling, thermoforming, etc.<br>4, thickness and stickiness of a reasonable combination;<br>5, the tensile strength and elongation of the protective film to ensure that the flexibility and strength of the protective film can meet the requirements;<br>6, the principle of film selection: full testing.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
Transparency and selection requirements of protective film<br>In the process of using the protective film, the adhesive types of the coating film include solvent rubber adhesive, solvent acrylic adhesive, water-based acrylic adhesive, and silicone adhesive. Among them, water-based acrylic adhesive is widely used in this kind of products. It can easily adjust the adhesion, and has good transparency and weather resistance.<br>The protective film is generally produced by CO extrusion, and its self-adhesive layer is generally EVA, ultra-low density polyethylene or polyolefin plastic resin. This structure form has gradually become the mainstream of the market, because it has more advantages than the coating film, such as no residual glue, providing stable adhesion, reducing user costs and creating higher profits for the protective film manufacturers.<br>First of all, the protective film should be viewed when the display is turned off. The method is the same as above. After each protective film is pasted in turn, the smaller the haze of the screen background color is, the better the material is. If the black test board is used, the difference is easier to see.<br>Another way to protect the film is to open a fluorescent lamp in a slightly dark room, tear off the protective film and put it between the eyes and the light with your hands. You should carefully see if there is a layer of fog like things evenly distributed in the protective film, which is the main cause of affecting the haze. The more serious this kind of fog like thing is, the greater the haze is, the worse the material is, and vice versa, (note) Haze can affect transmittance, but it is different from transmittance<br>Protective film because LCD is a sensitive device that is afraid of static electricity, the smaller the static electricity is, the better. The test method is to prepare the protective film to be tested (3-layer material or 2-layer material), smoke a cigarette and knock the ash on the desktop, or make some small paper scraps on the desktop, and then tear off the protective film above the protective film (this step is for 3-layer material), and then tear the protective film with silica gel Remove the protective film, and immediately move the use layer (silica gel surface) near the soot or paper scraps, to see whether the protective film will absorb these things to the silica gel layer of the protective film, and whether the absorption degree is strong. The stronger the static electricity is, the worse the material is, and vice versa.<br>Selection of protective film<br>1. Different surfaces need different viscosity;<br>2. The same similar surface different materials may also need different viscosity;<br>3. The subsequent processing step is the key to determine the viscosity. Follow up processing generally includes bending, stamping, cutting, drilling, thermoforming, etc;<br>4. Reasonable matching of thickness and viscosity;<br>5. The tensile strength and elongation of the protective film to ensure that the flexibility and strength of the protective film can meet the requirements;<br>6. Selection principle of protective film: full test.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: